The whole JP washed series filters has been certified by NSF to the standard of NSF/ANSI 42.
FEATURES
• NSF listed for ANSI 42 standard
•Through slope holes create real depth filtration and swirling flow
• Large flow and small pressure loss
• High dirt holding capacity and long service life.
• Pure, clean and washed material, no silicon, no fluorescence agent and no oil.
MAIN TECHICAL SPECIFICATION
• Dimension: Outer diameter Ø63±1mm Inner diameter Ø 28mm or Ø 30mm
• Maximum operating Pressure: 0.5MPa (72.5psi)
• Temperature: 60℃(140℉)
TYPICAL APPLICATIONS
• Residential water filter
• Food & Beverage
• Pre - RO
• Pharmacy & Hospital
• High quality industrial liquid filtration
• Other applications
TABLE 1
FLOW OF FILTER CARTRIDGE
The recommended flow for the filter cartridges in service is shown in the table (L/h for a 250㎜ filter cartridge)Micron Rate(μ m) | Viscosity |
1cs(water) | 30cs | 60cs | 120cs | 250cs |
0.5 | 70 | 60 | 40 | 25 | - |
1 | 150 | 90 | 60 | 40 | - |
3 | 300 | 120 | 80 | 50 | - |
5 | 500 | 170 | 120 | 60 | 45 |
10 | 800 | 300 | 140 | 70 | 60 |
20 | 1100 | 540 | 220 | 100 | 95 |
30 | 1200 | 670 | 300 | 150 | 130 |
50 | 1200 | 880 | 440 | 180 | 160 |
75 | 1200 | 1200 | 690 | 230 | 200 |
100 | 1200 | 1200 | 750 | 270 | 220 |
Notes:
1. The flow of each 250mm(10inch)filter cartridge should not exceed 1200 L/H (317G/H), otherwise its precision may be affected.
2. The flows shown in the above table are only the recommended values. The actual flow of the filter cartridge in service may change due to the liquid nature, temperature, the nature of the eliminated particles, the contents of the particles, etc.
3. It is recommended that a new filter cartridge used in the first time should work under a pressure drop of 0.1 - 0.3 bar (1.45 – 4.35psi ), while the final pressure drop for the filter cartridge exchange is set at 2.5 bar. For the filter cartridge whose precision is lower than 10μm, the pressure drop for the filter cartridge exchange had better be set at 1.0 -1.5 bar (14.5 – 21.8psi).
TABLE 2
PRESSURE DROP GRAPH
*pipe pressure loss excluded.
TABLE 3
DIRT HOLD COMPARISON
TABLE 4
ORDERING INFORMATION
SF W 20- 5 P 63 P 28 JP W
A B C D
SF | Brand name |
W | Filter type- W= string wound, PP= melt blown, PPL= PP pleated, CTO= carbon block |
A | Length- 10/20/30/40, inches. 250/500/750/1000, mm. |
B | Rating- 0.5/1/3/5/10/25/50/75/100/150/200 microns |
P | Yarn material- P= polypropylene, C= cotton, PE= polyester, GF= glass fiber |
C | Outer diameter: 60/63/110/152 mm |
P | Inner core material- P= polypropylene, S= stainless steel |
D | Inner diameter- 28/30/70/100mm |
JP | Series code- JP= JP series, HF= High Flow series |
W | Additional info- W= washed pure material, L= pure pp yarn, BB= big blue |
NSF link
http://info.nsf.org/Certified/DWTU/Listings.asp?Company=C0243330&Standard=042Raw material will be tested carefully assuring consistant quality. Following pictures are taken from our laboratory.